Android OS Forum banner
1 - 1 of 1 Posts

·
Developer
Joined
·
34 Posts
[adiv=ipsBox clear][adiv=ipsBox_container ipsPad][adiv=ipsLayout ipsLayout_withright ipsLayout_bigright clearfix][adiv=ipsLayout_content][adiv=ipsLayout_right][adiv=ipsPad ipsSideBlock]File Name: UnBrickable GalaxyS 4G
File Submitter: AdamOutler
File Submitted: 05 Nov 2011
File Updated: Today, 02:27 AM
File Category: Hardware
[aurl=/files/download/53-/]Download[/aurl][aurl=http://rootzwiki.com/index.php?app=downloads&module=display&section=changelog&file=53]Changelog[/aurl][aurl=/index.php?app=downloads&module=post&section=submit&do=edit_main&id=53]Edit Mod[/aurl][/adiv][/adiv][adiv=ipsLayout_content]Introduction
This is the DIY method to recover your device from a bad bootloader flash.The way this works is we change the OM value in the processor by modifying an individual electronic binary signal. The signal we are interested in is xOM5. This line is normally grounded, causing the overall OM value to equal 0x9. When we bring this line high, the OM value becomes 0x29. This reverses the booting order and ensures you will always have boot from USB available before the device starts.

This is a better option than JTAG for resurrecting a device. How could it possibly be better then JTAG? Let's count the ways....
1. The only part required is a wire.
2. No shipping time.
3. No cost for a box to interface the computer.
4. Permanent.
5. Can be done as a preventive measure.
6. Gives the ability to test new Bootloaders temporarily.
7. Allows development of the entire system.
8. Removes worry about flashing and acts as a backup.

After performing this mod:
Remove the battery, replace the battery, plug in USB, your phone will connect to the computer via USB and await commands. Otherwise it will pretty much act like an i9000 GalaxyS 4G. See the Special Instructions section.

Notes:
I've done quite a few of these guides now, this was the easiest-to-find UnBrickable Mod yet. Not only was it easy to locate, it's the cleanest, least tricky and easiest mod to apply as well. Please don't misunderstand this as being "easy", but it is easier than other devices.

I was able to overlay an annotated picture of a processor pinout over a picture of top of the T959V, then map out the shortest distance between the points on the processor



Part 1: Hardware Modification
You will need:
1. Get someone who knows what they're doing with a soldering iron. If they don't know what flux is, then they don't know what they're doing. PM myself or contact Connexion2005 if you don't know anyone else.
2. soldering iron - make sure it's sharp, if it's not sharp, then sharpen it, flux it and retin it.
3. flux
4. solder
5. tweezers
6. A relay (for the wire contained within)

Directions
1. Tear apart your device. Remove battery cover, battery, 7 screws, the back case and 5 connectors from the board.


2. remove the EM shield from the board to expose the resistors

3. Remove the xOM5 resistor and bridge the right pad to the resistor next to it.


4. Reassemble the device

Special Instructions
This replaces the battery charging sequence for the first few seconds of being plugged in.
To turn on the device, and operate in normal mode, you must hold the power button for 5 seconds.
3 button Download mode works as usual, however you must not have the S5PC110 drivers installed on the computer. You can use your custom rom menu option, adb reboot download, or use a terminal to "reboot download". 301Kohm Factory Mode JIGs work as well, but you must press power to bypass the S5PC110 mode.

Part 2: Software Based Resurrection

fw-D_cKeAb8

Unbricking:
1. Apply UnBrickable Mod to your device: see Hardware Modification section
2. Run ModeDetect and plug in your i9000. (Not a requirment, but helpful)
When you see this image you are in S5PC110 SEC SoC mode. When you see this mode you must proceed to step 3.


If it will only show this image, then you have not performed the modification correctly, or you have a hardware problem.


If it shows this, regardless of what's on your screen, you're in download mode:


3. Run UnBrickable Resurrector: Get it from the SVN repository here: http://code.google.c.../downloads/list This will only work on linux. Install Linux or dual boot if you have windows.


The resurrector will put your device into download mode
.

4. Now that you are in Download Mode, run Heimdall One-Click to flash firmware on your device. I've created a UVKF1 package here: http://forum.xda-dev...38#post19065238


5. repeat steps 3 and 4 with bootloader flashing enabled (Heimdall One-Click has a safety mechanism which requires you to flash once before flashing bootloaders).

Conclusion

Congratulations. You now have a device which works like a KIT-S5PC110 with an OM Value of 29. Now get to developing some serious custom software.

reading material
Creating your own Samsung Bootloaders: http://forum.xda-dev...d.php?t=1233273
KIT-S5PC110 manual: http://www.mediafire...94krzvvxksvmuxh
how to use DNW: http://tinyurl.com/dnw-how-to
Flash using openOCD and DNW: http://www.arm9board...OpenOCD_and_DNW
another DNW example: http://www.boardset....ucts/mv6410.php
ODroid dev center: http://dev.odroid.co...oot/wiki/#s-7.2

drivers and utilities
This will be an ever expanding list
Windows Drivers http://forum.xda-dev...37&d=1312590673
Windows Download Tool DNW: http://forum.xda-dev...38&d=1312590673
Windows Command Line tool: http://forum.xda-dev...23&postcount=27
Linux DNW Utility: http://dev.odroid.co...oot/wiki/#s-7.2
Linux ModeDetect tool: http://code.google.c.../downloads/list
Linux Automated UnBricker:http://code.google.c.../downloads/list

firmware
Bootloader Hello World by Rebellos http://forum.xda-dev...77&d=1314105521
UnBrick tool http://forum.xda-dev...d.php?t=1242466[/adiv][/adiv][/adiv][/adiv][/adiv]
 
1 - 1 of 1 Posts
Top